What are your concepts about Installing A Bathtub?
Installing a bath tub isn't precisely rocket science, yet it does require solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bath tub with a new one is additionally a moderately tough task. If the old bathtub is easily accessible, the job can move immediately; if you need to open a wall surface to eliminate the old bathtub and place the brand-new bathtub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will certainly need an assistant to move out the old tub and also set in the brand-new one. Make certain you have actually certified yourself for the task and are comfortable trying it. Rather than employing a service provider to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Possibilities are you might require a professional plumber to make tube links.
This article will assist you mount a new tub in your shower room if you have actually already purchased a new bathtub and don't require to transform the arrangement of your previous supply of water pipelines.
Your devices and product checklist should comprise the following:
Preparing for the Setup
First of all, the sustaining structure supplied with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to make certain that if the faucet features a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop pressure on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you make use of every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be suited its last setting.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is disconnect the water supply. After doing so, activate the taps to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be quite bothersome as a result of the restricted access that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a towel prepared for the remaining water that will originate from the pipes. Once the supply pipelines have actually been removed, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any kind of old sealing compound.
Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Bathtub
Making use of the two wooden boards under its feet, put the bathtub in the called for setting. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 small factors.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bathtub till the spirit level checks out degree.
To install taps, fit all-time low of the outermost versatile faucet connector to the suitable supply pipeline by making a compression join; then do the very same for the various other tap.
Turn on the water and inspect all joints and also brand-new pipework for leaks as well as tighten them if essential. Fill the bathtub as well as additionally check the overflow outlet as well as the typical electrical outlet for leakages.
Finally, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait until the tub has actually been made use of at least once as this will resolve it right into its last position.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will need minimizing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the placing opening in the bath/basin making certain that the washers are in place between the tap and the sink. Secure the tap in place with the producer offered backnut. As soon as the faucet is securely in place, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The former type should be connected to the tap ends first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the location where the bathroom satisfies the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split an inflexible seal, creating the water to pass through the wall surface in between the bathroom and the tiling, leading to problems with moisture as well as feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also installations. They are offered in tubes as well as cartridges, as well as are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched newspaper or soft rope. Remember to always load the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub remains in usage. The sealant can crack fairly very early if you do not think about this movement before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also easily readily available on the market. It is advisable to fit the ceramic tiles using water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been shown that editorial on How to Install a Bathtub through a good friend on our other web address. Do you know about anybody else who is truly interested in the niche? Feel free to promote it. I am grateful for your time. Come back soon.
Apply Now